meterbridge66

Fiat 500 Replacement Key Fob If your 500 remote key fob has stopped working, it's time to replace the battery. However, if you replace the battery but it continues to stop working then the issue could be elsewhere. United Locksmith specializes in the creation of new keys for classic vehicles. We have all the tools and parts necessary for this type of service. Dead Coin Battery The most frequent reason that your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The key fob comes with the battery of a coin-cell that will drain quickly in the event that it is not used often enough. If your remote starts to show signs like a loss in range or stopped working, then the battery may be dead. The battery in the key fob is held in place with metal clips for retaining. If the clips are not tight, they can create problems with contact that can prevent your remote to receive power. Use a flathead screwdriver to open the retaining clips and remove the battery. Make sure to select a replacement with the same type of voltage, size, and specification as the original battery. The exposure to water can cause the key fob to become corroded or damaged. Even a brief bath in soapy water can harm the electronic chip within. It's best to keep your key fob in a dry area. Water Damage Damage to your water supply could be the reason for your key fob not working properly. The rubber seals on key fobs stop them from being damaged by a slight splash or drizzle of water. However, sneak a peek here is essential to keep the car keys away from the washing machine, ocean, and pool. The key fob has an electronic chip that transmits a message to the immobilizer system of your car. The chip is what allows the 500 to be locked and started. If it gets wet, however it will not function. If you're looking to determine whether your key fob functional it is possible to clean the internal electronics using isopropyl or electronic cleaner. It is best to replace the key fob when it has been submerged into salt water rather than attempting to repair it yourself. A replacement fob could cost you a little bit however, it's less expensive than paying to have your Fiat 500 towed to a dealership and repaired there! You can also do it yourself by following only a few steps. Make sure you have the correct type of battery before attempting to open your key fob. This task is more straightforward than it appears, and you can find step-bystep instructions online for almost any car key fob. Faulty Chip The chip inside the key fob communicates to your car's immobiliser unit to ensure the vehicle is only able to start when the correct key is used. If the chip is damaged or corrupted in any way, your car will not start. A chip that is damaged can happen due to many reasons, but most commonly due to water damage or the battery being dead. It is best to delegate the work to a professional locksmith who can repair the chip in a short time and at a a reasonable price. If your key fob stops functioning after exposure to clean water from the tap or rain, take off the battery and wipe down the electronic component with a paper towel to ensure it is fully dry before putting it back into. If the key fob does not function, there is an opportunity that it is a fried component and needs to be replaced. Some people will turn to their dealer when they are in need of a new Fiat key fob, however it can be a costly alternative. United Locksmith is the best choice if you want your Fiat key fob replaced at a reasonable price. We have the tools and expertise necessary to fix your Fiat key fob in a timely and professional manner. Faulty Receiver Module Fiat key fobs send signals of up 50 feet to the vehicle, which allows it to unlock and close the doors (and start the vehicle for vehicles with automatic transmissions). There are a variety of reasons why a fob could stop working. This includes a dead battery or water damage, worn-out buttons an issue with the receiver, signal interference or an issue with the chip. If the fob is in the pocket that has been subject to extreme trauma (such as being dropped onto a hard floor or being washed in the washing machine) the fob might not be able to connect with the Body Control Module (BCM) of the vehicle. This is because the BCM is an extremely secure system that will only accept signals from a genuine key and not any other. You will need to replace the fob if this happens. A locksmith professional can handle all aspects of the replacement procedure as well as programming a new one for the 500. They can even offer a clone fob that works just like the original (and costs only one-third of the price).